Drawings
Updated
A PDF document (525 KB) attached to Full and Open Opportunity for MK68 Spare and Repair Parts Fabrication IAW the attached NAVSEA Drawing, SOW, and ALL additional attachments. Provide your Cage Code on the Quote and Submit the Cost Breakdown Spreadsheet., from the Department of the Navy. Due Nov 4, 2026, 11:00 AM (UTC-6).
File name: A04 DWG 8905617.pdf
The full file is for paid members, or buy this bid alone.
Preview
CUI
NOTES:
D
REVISIONS
ZONE
1. EYES TO BE SPLICED USING A LOCKED BRUMMEL SPLICE. SPLICE TO BE .38 WITH
A LENGTH OF 1.25 .25 TO SPLICE. THE BURIED TAIL OF THE COMPLETED SPLICE
SHALL HAVE A MINIMUM LENGTH OF 2 IN. UPON COMPLETION OF SPLICE, APPLY
THREE STITCHES IN ACCORDANCE WITH ASTM D6193 TYPE 205 STARTING AT THE
BEGINNING OF THE SPLICE AND PROGRESSING TOWARDS THE END OF THE TAIL
ON THE SAME PLANE USING THREAD, FN 14. RETURN STITCH BACK TO BEGINNING
OF SPLICE APPLYING STITCH PERPENDICULAR TO ORIGINAL PLANE IN
ACCORDANCE WITH ASTM D6193 TYPE 205. SECURE LOOSE ENDS TOGETHER
WITH TWO OVERHAND KNOTS.
5.
7.
5.
1.
REV.
DESCRIPTION
-
CONFIGURATION CONTROL
DATE
12X 9
APPROVED
D
7.
.50±.06
2. FOR PRE-COILED LENGTH AND INSPECTION REQUIREMENTS, SEE SHEET 2.
3. COILS TO BE POSITIONED SO THAT THERE IS A MINIMUM 1.0
FEATURES.
.5 IN. BETWEEN
6.
5. PROOF LOAD AMSTEEL DYNEEMA, FN 7, AFTER INDUCING COIL VIA HEAT SHRINK
FN 11 AND PRIOR TO REDUCING HEAT SHRINK FN 12 OVER FUSIBLE LINK FN 3, TO
500 LB. DO NOT LOAD FUSIBLE LINK, FN 3 IN 500 LB. PROOF LOAD.
6. PRIOR TO REDUCING HEAT SHRINK, FN 12, OVER FUSIBLE LINK, FN 3, AND AFTER
SWAGING 12 X SLEEVE, FN 9, SEPARATELY PROOF LOAD EACH OF THE THREE
WIRE ROPE, FN 10, TENSION MEMBERS TO 100 LBS FOR A MINIMUM OF 5 MINUTES. DO NOT LOAD FUSIBLE LINK, FN 3, IN PROOF LOADS.
7. PROOF LOAD ASSEMBLY AT LOCATIONS INDICATED BY 7
FUSIBLE LINK) TO 60 LBS PRIOR TO COILING.
6.
6.
1 53711-8905617-1
4. SECURELY FASTEN TIE DOWN STRAP, FN 13 UNTIL SNUG, CLIP EXCESS MATERIAL
BEYOND THE STRAP OFF.
C
6.
6.
.75±.25
C
8.
(INCLUDING THE
8. STITCH A SEAM IN LOCATION SHOWN ACROSS WIDTH OF HOOK STRAP, FN 5, FOLDED IN HALF ABOUT D-RING, FN 6, IAW ASTM D6193 TYPE 205 WITH THREAD,
FN 14. STITCH WITH HOOK SIDES OF STRAP FACING INWARD. SECURE ENDS OF
SEAM WITH BARTACK STITCHES AS DEFINED IN SECTION 3.1.1 OF ASTM D6193.
9. ITEM(S) MAY BE PURCHASED FROM LISTED VENDOR OR DESIGN ACTIVITY
APPROVED EQUIVALENT.
B
AR
TYPE II, CLASS 1, SUB A
THREAD, POLYESTER, SIZE 207 TEX 210
MS3367-4
STRAP, TIE DOWN
AR
M23053/5-1-107-9
AR
M23053/5-1-105-9
INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE,
POLYOLEFIN, FLEXIBLE, CROSSLINKED
INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE,
POLYOLEFIN, FLEXIBLE, CROSSLINKED
AR
65196
SY06377LD
1/16 IN. DIA. 7 X 7 CRES WIRE ROPE
STAINLESS STEEL
MIL-DTL-18375
65196
MS51844-62
SWAGING - WIRE ROPE SLEEVE
STAINLESS STEEL
MS51844
65196
AN100C-3
THIMBLE - WIRE CABLE
STAINLESS STEEL
AN100
AR
3A3T8
872007206030
AMSTEEL-BLUE 7/64 D BLACK
DYNEEMA, HMPE
SAMSON, AMSTEELBLUE
0KVE6
30375T42
1-1/2" D-RING
STAINLESS STEEL
53711
9008064-1
HOOK STRAP
53711
8719642-1
The beginning of the document. Download the full file to read on.