Amendment 4- - BID - 050 - S-101 STRUCTURAL PLAN (R2)

01 CLEAN, PATCH, AND LEVEL CONCRETE SLAB AND COVER WITH

A

A

KEYNOTES

AN APPLICATION OF A PAINTED EPOXY FINISH WITH NON-SLIP

GRIT ADDED. SEE MAINTENANCE GARAGE NOTES.

02 CLEAN AND RESEAL CONCRETE SLAB.

58'-114"
21'-1114"

32'-8"

03 PCC SLAB

04 EXPANSION JOINT

NOTES

B

B

8'-0"

SAWCUT 4"x 4" GROOVE TO BULLNOSE COATING EDGE.

05 COORDINATE

LOCATION WITH THRESHOLD INSTALL.

17'-1"
19'-1"

MAINTENANCE GARAGE FLOOR

1.

CLEAN TO REMOVE ALL SOLUBLE SURFACE CONTAMINANTS.

REMOVE ALL UNSOUND CONCRETE. MECHANICALLY PREPARE TO

REMOVE ALL INSOLUBLE SURFACE CONTAMINANTS AND ACHIEVE

AN ICRI CSP 3. VERIFY MOISTURE LEVELS ARE IN ACCORDANCE

WITH MANUFACTURER'S INSTRUCTIONS.

7'-9"

32'-8"

2.

SURFACE PREPARATION:

COATING SYSTEM:

·
·
·

C

WEATHERPROOF STORAGE, SEE SHEET AE-131.

ANCHORAGE TO SLAB IN ACCORDANCE WITH

MANUFACTURER'S RECOMMENDATIONS

STRUCTURAL PLAN - MAINTENANCE GARAGE

·

SCALE: 1/4" = 1'-0"

·
·
·

PRIME ALL SURFACES WITH TNEMEC SERIES 66, 161OR

205 EPOXY AT 3.0-5.0 DRY MILS.

PATCH ALL VOIDS AND FILL TO FLUSH WITH A MORTAR

MIX OF TNEMEC SERIES 237 AND SAND.

V-GROOVE THE CRACK 1/8” WIDE AND FILL TO FLUSH

SERIES 206 SUBFLEX.

BROADCAST FINE SAND INTO THE SERIES 206 TO KEEP

RECOAT WINDOW OPEN.

APPLY TNEMEC SERIES 206 TO ALL SURFACES AT 40-50

DRY MILS (35-45 SQ FT/GAL).
LIGHTLY SAND THE SERIES 206 TO DEGLOSS.

APPLY FINAL COAT (SEE AE-602)

C

BRICK STABLE FLOOR

1.

SURFACE PREPARATION:

CLEAN TO REMOVE ALL SOLUBLE SURFACE CONTAMINANTS.

REMOVE ALL UNSOUND CONCRETE. MECHANICALLY PREPARE TO

REMOVE ALL INSOLUBLE SURFACE CONTAMINANTS AND ACHIEVE

AN ICRI CSP 3. VERIFY MOISTURE LEVELS ARE IN ACCORDANCE

WITH MANUFACTURER'S INSTRUCTIONS.

·

26'-8"

D

COATING SYSTEM & CRACK REPAIR:

·

·
·

·

EL. 936.0

1'-6"

E

#4 HOOP @ 12" O.C.

2'-0"

(6) #4 BAR

6"

REQ'D GEOTEXTILE

FABRIC

17'-1"

REQ'D CRUSHED

AGGREGATE

S-101

SECTION - WEATHERPROOF STORAGE SLAB

SCALE: 1/4" = 1'-0"

F

SCALE: 1-1/2" = 1'-0"

STRUCTURAL PLAN - BRICK STABLE

F

17'-2"

2% SLOPE

14'-4"

REQ'D PCC SLAB

EXPANSION JOINT

E

·
·

PRIME ALL SURFACES WITH TNEMEC SERIES 66, 161OR

205 EPOXY AT 3.0-5.0 DRY MILS.

PATCH ALL VOIDS AND FILL TO FLUSH WITH A MORTAR

MIX OF TNEMEC SERIES 237 AND SAND.

V-GROOVE THE CRACK 1/8” WIDE AND FILL TO FLUSH

SERIES 206 SUBFLEX.

BROADCAST FINE SAND INTO THE SERIES 206 TO KEEP

RECOAT WINDOW OPEN.

APPLY TNEMEC SERIES 206 TO ALL SURFACES AT 40-50

DRY MILS (35-45 SQ FT/GAL).
LIGHTLY SAND THE SERIES 206 TO DEGLOSS.
APPLY TNEMEC SERIES 248 AT 2.0-3.0 DRY MILS.